Introduction

SONOFF Wi-Fi Smart Switch

User Manual

Remote Control

LAN Control

Group Control

Compatible Voice Assistants

Specification

Model

BASICR4

MCU

ESP32-C3FN4

Input

100-240V ~ 50/60Hz Max 10A

Output

100-240V ~ 50/60Hz Max 10A

Max. Load

2400W@240V

Wireless Connectivity

Wi-Fi IEEE802.11b/g/n2.4GHz

Net Weight

47.3g

Dimension

88x39x24mm

Color

White

Casing Material

PC V0

Applicable Place

Indoor

Working Temperature

-10℃~40℃

Working Humidity

5%~95% RH, non-condensing

Certification

ISED/FCC/RoHS/ETL/CE/SRRC

Executive standard

EN IEC 60669-2-1, UL 60730-1, CSA E 60730-1

Download the“eWeLink”App

Please download the “eWeLink” App from Google Play Store or Apple App Store.

Installation

1. Power off

*Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection or contact the terminal connector while the device is powered on!

2. Wiring instruction

To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 10A has been installed before the BASICR4.

Wiring: 16-18AWG SOL/STR copper conductor only, Tightening torque: 3.5 lb-in

*Make sure all wires are connected correctly.

3. Power on

After powering on, the device will enter the Pairing Mode defaulted during the first use, and the LED indicator flashes in a cycle of two short and one long.

*The device will exit the Pairing Mode if it is not paired within 10mins. If you want to enter this mode again, please long press the button for 5s until the LED indicator flashes in a cycle of two short and one long and then release.

Add a Device

1.Download the“eWeLink”App

Please download the “eWeLink” App from Google Play Store or Apple App Store.

2.Add device

Please follow the wiring instructions to connect the wires (ensure power is disconnected in advance and consult an electrician if needed)

Power on the device

Scan the BASICR4 QR code on the device body

Long press the button for 5 seconds

Select the “Wi-Fi” network and
enter the password

Device“Added completely”

Device Function

1. Magic Switch Mode

After short-circuiting the L1 and L2 of the switch terminals through the wires, the device can still be online and can be controlled through the APP after the users flip the wall switch to turn off/on the light.

• Add a wire to connect L1 to L2 on the wall switch following the manual, and the device will stay online even when you switch it off via the wall switch after “Magic Switch Mode” enabled.

• The “Power-on State” will automatically be set to OFF, to make the “Magic Switch Mode” functional when enabled.

• The “Magic Switch Mode” will automatically disable after your adjustment to the “Power-on State”.

Note: Only compatible with mainstream brands of double pole rocker switches Rocker switches. The rear-end light needs to be compatible with mainstream brands of LED, energy-saving lamps, and incandescent lamps ranging from 3W to 100W.

*This function also applies to dual-control lamps

2.Auxiliary overheating protection

With the product built-in temperature sensor, real-time maximum temperature of the entire product can be detected and speculated, which prevents the product from deformation, melting, fire or live devices exposing in case of over-temperature.

The device automatically cuts off the load when it gets too hot. To exit the overheating protection mode, simply press the button on the device after confirming that the load is functioning normally without any internal shorts, excessive power, or leaks.

*Please note that this function only serves as auxiliary protection and cannot be used in place of a circuit breaker.