Introduction
Matter Over WiFi Smart Switch
User Manual V1.0
The MINI-1GS10 is a compact Wi-Fi single-channel smart switch with neutral and live wires required. It can be installed in a wall switch box and supports loads of up to 10A, allowing a conventional switch to be upgraded to a smart switch. It supports Matter, local Web control, and local API, enabling seamless integration with multiple smart home ecosystems for flexible and reliable home automation.
Remote Control
Matter Support
Smart Timer/Delay
Local Web Control
Voice Control
Local API
Detach Relay Mode
Supports loads up to 10A
① Button
-
Single press: Turn on/off the smart device. -
Press and hold for 5 seconds: The device enters pairing mode while simultaneously enabling the AP hotspot. -
Press and hold for 10 seconds: Factory reset. -
Press three times in succession: Switch the external switch type.
②
Blue
-
Steady on: Connected to the Internet. -
Flash three times quickly: Switch the external switch trigger type.
Red
-
Flashes two short and one long: Device is in pairing mode. -
Keeps on: LAN only. -
Slow flashing: Offline. -
Fast flashing: Factory reset.
Platform Certification
Specification
MINI ONE (Matter Over WiFi)
Product Series
MINI Extreme Series Gen5
Product Name
Matter Over WiFi Smart Switch
Product Model
MINI-1GS10
MCU
ESP32-C6
Rating
10A 100-240V~ 50/60Hz Max Resistive load μ
WiFi
IEEE 802.11 b/g/n/ax 2.4GHz
Net Weight
27.3g
Dimensions
39.5×33×16.8mm
Color
White+Orange
Housing Material
PC
Recommended Wire Gauge
18 AWG to 14 AWG (0.75mm² to 2.5mm²) SOL/STR copper conductor only
Installation Location
Indoor concealed installation
Operating Temperature
10T40 (-10℃~40℃)
Operating Humidity
10% ~ 90% RH, non-condensing
FCC ID
2APN5-MINI1GS10
Certifications
CE/RoHS/FCC
Installation
1. Power Off
③For single-phase use only (100-240V~). Connecting to a multi-phase power supply may damage the device.
2. Wiring Instruction
|
Terminal |
|
Wire |
|
|
N |
Neutral wire |
N |
Neutral wire |
|
L In |
Live wire |
L |
Live wire (100-240V~) |
|
L Out |
Live wire output terminal |
Load |
|
|
S1 |
Switch |
|
|
Do not connect the S1 terminal to the neutral or ground wire, as this may damage the device and cause a hazard.
Ensure the wiring is correct.
The external switch type supports toggle switches and momentary switches. The default factory setting supports toggle switches.3. Power On
After power-on, the device enters pairing mode by default for first-time use, with the LED indicator flashing in a pattern of “two short and one long”.
If no pairing is performed within 10 minutes, the device exits pairing mode. To re-enter pairing mode, press and hold the button for 5 seconds until the LED indicator changes in a cycle of two short and one long flash, and release.Matter Ecosystem User Guide
Open a Matter-compatible App to scan the Matter QR code on the Quick Guide or the device itself to add the device.
Add to Apple
via Matter
Add to Google
via Matter
Add to Alexa
via Matter
Add to SmartThings
via Matter
Add to Home Assistant
via Matter
eWeLink Ecosystem User Guide
①
Please download the “eWeLink” App from Google Play Store or Apple App Store.
② Add Device
Enter “Scan”
Scan the QR code on the quick guide or the device
Select “Add Device”
(If the device exits pairing mode)
Long press the button for 5 seconds
Check LED indicator flashing status
(Two short and one long)
Search for the device and start connecting
Select the “Wi-Fi” network and enter the password
Device “Added completely”
Web Console Guide
Method 1: Access via AP Hotspot
Connect to the device hotspot SONOFF_1GS_xxxx, then enter the following in your browser:
to access the Web Console.
Method 2: Access via LAN
in your browser to access the Web Console.
Install the Device in an Electrical Box
Factory Reset
Trigger conditions (any one condition met)
-
Click “Restore Factory Settings” on the eWeLink App. -
Click “Restore Factory Settings” in the web control page. -
Press and hold the button for 10 seconds.