Introduction
Zigbee Smart Switch
User Manual
The MINI-ZB1GSP is a compact Zigbee 3.0 single-channel neutral-and-live-wire switch with power monitoring capability. It can be installed in a switch junction box and supports a maximum load of 16A, turning a regular switch into a smart switch. With repeater functionality, it easily improves Zigbee communication quality and can also be linked with other devices in smart scenes to realize your home automation.
Remote Monitoring
Power-On State
Repeater Function
Supports loads up to 16A
Voice Control
Inching Mode
Energy Monitoring
One Year of Historical Data
① Button
- Single press: Turn the device on or off
- Press and hold for 5 seconds: Device enters pairing mode (Zigbee pairing + Bluetooth pairing, pairing lasts for 3 minutes).
- Short-press once, then press and hold for 5 seconds within 3 seconds: Activates Bluetooth pairing mode (only effective after pairing with a Zigbee gateway).
- Press and hold for 10 seconds: Factory reset.
② LED Indicator (Blue)
- Slow flashing for 180 seconds: First power-on, entering pairing state (Zigbee pairing + Bluetooth pairing).
- Steady off: Pairing failed/timed out.
- Steady on: Connected to the gateway normally.
- Fast flashing: Abnormal connection to the gateway.
- Flash three times quickly: Switch the external switch trigger type.
- Two fast flashes followed by one slow flash: Bluetooth pairing mode active.
Platform Certification
Specification
Product Series
MINI Extreme Series Gen5
Product Name
Zigbee Smart Switch
Product Model
MINI-ZB1GSP
MCU
EFR32MG21
Rating
16A 100-240V~ 50/60Hz Max Resistive load
Zigbee
IEEE 802.15.4
Net Weight
27.3g
Dimensions
39.5 × 33 × 16.8mm
Color
White+Green
Housing Material
PC
Recommended Wire Gauge
18 AWG to 14 AWG (0.75mm² to 2.5mm²) SOL/STR copper conductor only
Installation Location
Indoor concealed installation
Operating Temperature
-10℃ ~ 40℃
Operating Humidity
10%~90% RH, non-condensing
FCC ID
2APN5-MINIZB1GSP
Certifications
CE / RoHS / FCC
Installation
1. Power off
② To ensure safe electrical installation, a miniature circuit breaker (MCB) or residual current operated circuit breaker (RCBO) rated at 16A and compliant with national safety standards must be installed ahead of the MINI-ZB1GSP.
③ For single-phase use only (100-240V~). Connecting to a multi-phase power supply may damage the device.
2. Wiring Instruction
|
Terminal |
|
Wire |
|
|
N |
Neutral wire |
N |
Neutral wire |
|
L |
Live wire |
L |
Live wire (100-240V~) |
|
L |
Live wire |
L |
Live wire (100-240V~) |
|
L Out |
Live wire output terminal |
Load |
The two L Out terminals are internally connected for wiring convenience only and do not increase the rated current capacity. |
|
L Out |
Live wire output terminal |
Load |
|
|
S1 |
Switch |
|
Do not connect the S1 terminal to the neutral or ground wire, as this may damage the device and cause a hazard. Ensure the wiring is correct. The external switch type supports toggle switches and momentary switches. The default factory setting supports toggle switches.
3. Power On
After power-on, the device enters pairing mode by default for first-time use, with the LED slowly flashing.
If no pairing is performed within 3 minutes, the device exits pairing mode. To re-enter pairing mode, press and hold the button for 5 seconds until the LED slowly flashes.Download the eWeLink App
Please download the “eWeLink” App from the Google Play Store or Apple App Store.
Add a SONOFF Zigbee Gateway
Compatible Gateways：
Recommended SONOFF gateway models: ZBBridge-P, ZBBridge-U, NSPanel Pro, iHost
Other compatible SONOFF gateway models: ZBDongle-P, ZBDongle-E
Add Device
Method 1: Scan QR Code
Open “Scan” in the app
Scan the QR code on the device
Select “Add Device”.
(If device exits pairing mode) Press and hold the button for 5 seconds
Check that the LED is slowly flashing
Select the Zigbee gateway
Add device and select “Finish”
Method 2: Activate Gateway Pairing Mode
Press and hold the button for 5 seconds to confirm the device enters pairing mode
Check that the LED is slowly flashing
Select the gateway on the eWeLink app home page
Find and click “Add Device” in the gateway page
Install the Device in the Mounting Box
Factory Reset
Trigger conditions (any of the following):
- Delete the device from the eWeLink App.
- Press and hold the button for 10 seconds.